|
|
| Register | Forums | Blogs | Today's Posts | Search | Donate |
 |
 |
 |
|
#11
12-14-2012, 11:15 AM
|
|||||
|
|||||
Quote:
The pistol so far is exceeding expectations. It's a thing of beauty. We've got a basic plan to finish it down to high gloss (something like 1000), and send it off in pieces to Glenrock for bluing. That process should be quick and inexpensive since the real expensive and time consuming part for them is disassembly/assembly, and finishing. Doc, apparently nobody does Royale Blue except Colt. Glenrock does not, and doesn't know anyone else who does. Is there something I'm missing? Also, as you, I really like the look of Royal Blue, but do you think it's appropriate as a finish for a working/carry gun. I'm planning on this pistol being my go to weapon, not a closet queen.  , I'll be needing some slim, bobtail camel bone grips right soon!
__________________
If you love wealth more than liberty, the tranquility of servitude better than the animating contest of freedom, depart from us in peace. We ask not your counsel nor your arms. Crouch down and lick the hand that feeds you. May your chains rest lightly upon you and may posterity forget that you were our countrymen. -- Samuel Adams COTEP CBOB0676 KO4ENQ 
|
|
#12
12-14-2012, 03:41 PM
|
|||
|
|||
|
The Journey Continues...
Barrel and bushing hard fit, slide fit and laoped. Ignition parts tuned for 4 lbs pull (glass break vice roll) Still waiting for the Novak thumb safety. Next up....tune feeding for defense loads (already feeds Ball  )Pics:     
|
|
#13
12-14-2012, 03:46 PM
|
|||||
|
|||||
|
Thanks namman and
for the Updates.....and new Pics......
__________________
CBOB:0002 1905 Savage 380, 1978, 1980 DW Pistol Pacs, Severns Custom 1985 Springer 1911A1, 09 DW Marksman, S&W Model 19-6, GSG 1911 22LR. , S&W Model 29-2
|
|
#14
12-14-2012, 04:04 PM
|
|||||
|
|||||
|
Quote:
i was planning on ordering some more camel scales tomorrow so i should get them by the end of next week.
__________________
Criminals thrive on the indulgence of society's understanding. I have no such indulgence nor understanding of criminals. Neither does my .45.
|
|
#15
12-14-2012, 06:59 PM
|
|||||
|
|||||
|
Quote:
__________________
If you love wealth more than liberty, the tranquility of servitude better than the animating contest of freedom, depart from us in peace. We ask not your counsel nor your arms. Crouch down and lick the hand that feeds you. May your chains rest lightly upon you and may posterity forget that you were our countrymen. -- Samuel Adams COTEP CBOB0676 KO4ENQ
|
|
#17
12-16-2012, 09:00 PM
|
|||||
|
|||||
|
Looking good!!!
__________________
"This is the 44 Magnum AutoMag and holds a 300 grain cartridge and if properly used can remove the fingerprints"!! COTEP # CBOB0152
|
|
#19
12-18-2012, 04:44 PM
|
|||
|
|||
|
I'll get some more pics up later but here is a question for you all...
How do you fix an (in my opinion) unacceptable gap under the blade (not the dovetail) of the front sight blade? Unacceptable to me is anything over .0001 (yes that is 3 zero's or 1 ten thousandth of an inch). BTW it has already been fixed and the install is good to go. 
|
|
#20
12-19-2012, 04:16 PM
|
|||
|
|||
|
Really, no guess'....
Alright then. I use silver solder to add just a few thousandths under the blade, then mill or file to fit. The cold blue in the following pics is to see how much (if any) of the silver solder remains, the goal being as little visible as possible (especially if the gun is to be blued like this one, blueing doesn't like silver solder). Not sure how clear it is in the pics, but there is no visible solder to affect the blueing. The blend job is almost complete. What appears to be a slight gap between the frame rails and the bottom of the slide is actually just a minute bevel on the back edge of the slide rails. The rear sight is a 10-8 U notch and the front is an SDM Gold Bead, now fit with zero gap under either. The rear of the slide has been blended with the frame, extractor and ejector, still needs to be finished...enjoy. No, that is not the thumb safety that will end up on the build, waiting for a NOVAK (if not I have an EGW that will get reprofiled.)    
Last edited by navman; 12-19-2012 at 04:19 PM.
|
). Smooth as oiled glass on glass. Wilson combat barrel hood and upper lugs fit to slide, bushing still needs to be final lapped in, tight as all hell right now.
Linear Mode
