|
|
| Register | Forums | Blogs | Today's Posts | Search | Donate |
 |
 |
 |
|
#1
07-03-2017, 07:20 AM
|
|||||
|
|||||
Colt Custom Delta Elite build Piper Custom
Just picked this up from Piper Custom. He did this Colt Custom Build for me. The grips are my "Starry Night" grips, although I'm sure that's not what Sarge from The Finer Grain calls them. I've been trying various grips to see what I like best.
I don't have my photo setup any more so these are just iPhone pictures after greasing it up for the range. I hope to take it out for a spin soon.               
__________________
COTEP CBOB #289 "Deserve's got nothing to do with it". Last edited by dwsmithjr; 07-03-2017 at 07:25 AM. 
|
|
#2
07-03-2017, 07:26 AM
|
|||||
|
|||||
|
Heinie sight set...............
Wilson gold bead front sight... EGW bushing.................... EGW slide stop................. Wilson Extractor............... EGW Ejector.................... EGW thumb safety............... EGW grip safety................ EGW guide rod.................. Wilson hammer.................. EGW sear....................... EGW disconnector............... STI firing Pin................. EGW firing pin stop............ Stan Chen mainspring housing... 10-8 magazine catch............ Greider trigger................ Wolff sear spring.............. Wolff recoil spring............ EGW grip screws................ Here is a list of the work done. High cut frontstrap, hand checker 25 lpi, bordered Machine frame for Chen mainspring housing, blend, round heel, checker 25 lpi. Machine & hand bevel mag well Cut frame, fit & blend grip safety, convert to series 80 Fit, re shape & blend thumb safety Fit & blend oversized slide stop, shorten &round, recess & chamfer frame hole Fit magazine release, blend Fit trigger Fit oversized firing pin stop Machine slide for front and rear sights Fit & tune extractor Fit oversized bbl bushing on lathe & blend Machine slide- live round eject, flare ejection port True & polish breech face Fit, cut, tune ejector & blend 30 degree recessed & polished flush crown Serrate rear of slide 40 lpi Machine feed ramp 31.5 degrees & hand polish Re cut bbl throat & polish Smooth & fit all fire control parts. Trigger job 4.5 lbs De burr/ de horn gun and all parts Satin bead blast, hand polish slide flats 400 grit Test fire- silver tip, hydra shok, & norma. All ok
__________________
COTEP CBOB #289 "Deserve's got nothing to do with it".
|
|
#3
07-03-2017, 07:27 AM
|
|||||
|
|||||
|
Very nice !
__________________
Rich COTEP #762 A gun is a tool, no better or no worse than any other tool: an axe, a shovel or anything. A gun is as good or as bad as the man using it. Remember that. And shepherds we shall be, for Thee, my Lord, for Thee. Power hath descended forth from Thy hand, that our feet may swiftly carry out Thy command. So we shall flow a river forth to Thee, and teeming with souls shall it ever be. In nomine Patris, et Filii, et Spiritus Sancti.
|
|
#5
07-03-2017, 10:10 AM
|
|||||
|
|||||
|
My wallet was traumatized for sure, but not all at once, over the course of about a year and a half, first the base gun, then the parts, then the work. It's still cowering in the corner though.
__________________
COTEP CBOB #289 "Deserve's got nothing to do with it".
|
|
#9
07-03-2017, 10:20 PM
|
|||||
|
|||||
|
Sweet 10mm Dennis. I'm curious about the series 80 conversion. I thought most people go the other way and convert to series 70? Did you add in the firing pin safety block?
|
Linear Mode
