COTEP.org  

Go Back   COTEP.org > Main Category > COTEP University

Reply
 
Thread Tools Display Modes
  #1  
Old 09-19-2014, 04:44 PM
Dave Waits's Avatar
Dave Waits Dave Waits is offline
Founding COTEP Member who is watching over us from above with God at a giant shooting range in heaven
COTEP Member
 
Join Date: Apr 2011
Location: Loveland, Ohio
Posts: 928
Thanks: 4
Thanked 229 Times in 59 Posts
Default Specs for Garands

HELPFUL INFO FOR GARAND-DRIVERS


VARIOUS SPECS
1.) Op-Rod Specs;
a.) Piston Dia.; Min. Diameter- 0.5256
b.) Out of Round; No more than .00035
c.) Tab specs; Height- .320(min..317), Width-.250, Thickness-.100(Min..097)

2.) Gas-Cylinder Front-end; 0.532

3.) Gas-Port; 30-06-.079(use #47 drill bit to check, No-Go is #45 bit)
.308- A little nebulous. Depending on Manufacturer anywhere from .096 to .107.

4.) Sight adjustments(Come-ups) Based on 100 yard zero.
a.) 200 yards-two clicks up from 100 yard zero
b.) 300 yards-five clicks up from 100 yard zero
c.) 500 yards- twelve clicks up from 100 yard zero
d.) 600 yards- sixteen clicks up from 100 yard zero

5.) Targeting front sight
a.) sight correction with M1 Garand is .008= 1-inch at 100 yards
b.) Formula; (Sight Radius in inches)x(Impact point distance from point of aim)/(Range to target in yards)x(36” per yard)=sight correction.
c.) (28”,sight radius of M1)x(1” from point of aim)/(100 yards)x(36)=.008
d.) Say you need 18 clicks of elevation to zero at one-hundred yards. Optimal
Elevation amount is six clicks for proper use of sight. So;
(28” times 12{18 clicks minus 6}/(100 times 36)= .093
336/3600=.093
So, filing the front sight down by .093 will put you at zero with six clicks at 100 yards. This is assuming proper trigger-guard tension and a tight lower-band(Both have the effect of raising point of impact through loss of downward pressure).

6.) Checking Lubrication through ejection
a.) Properly lubed- First seven rounds between 1 O’Clock and 2:30(barrel direction is 12:00),with round #8 at 3:00.
b.) Ejection at 12:00 to less than 1:00- Over-lubricated
c.) Ejection past 2:30- Under-Lubed or dirty

7.) Grease-Lube point on Garand
a.) Bottom of barrel from 1” in front of receiver to 3”.
b.) Op-rod Tab Track
c.) Camming Surface in Hump of Op-rod
d.) Bolt-camming lug on Hammer
e.) Inside rear-lip of receiver
f.) Locking recesses of receiver(Bolt-lug slots)
__________________
Diligentia, Vis, Celeritas
COTEP#CBOB0428
NRA,GCA,OGCA, USAF,Msgt.(Ret.)
Reply With Quote
The Following 7 Users Say Thank You to Dave Waits For This Useful Post:
AutoMag (09-19-2014), Caleb (09-20-2014), DaFadda (09-20-2014), Pawpaw (09-19-2014), Riverpigusmc (09-19-2014), ronpaul50 (09-19-2014), sdmc530 (09-19-2014)
  #2  
Old 09-19-2014, 08:35 PM
Pawpaw's Avatar
Pawpaw Pawpaw is offline
Founding Member
COTEP Member
 
Join Date: Nov 2011
Location: North Texas
Posts: 243
Thanks: 85
Thanked 19 Times in 4 Posts
Default

That's some great info. Thanks!
__________________
COTEP# CBOB0569
Reply With Quote
  #3  
Old 09-19-2014, 11:30 PM
Grizzman Grizzman is offline
Founding Member
COTEP Member
 
Join Date: Apr 2011
Location: Shawnee, KS
Posts: 527
Thanks: 18
Thanked 20 Times in 4 Posts
Default

Thanks, Dave!!
__________________
COTEP #CBOB0353
Happiness is a warm, dirty gun.
Reply With Quote
  #4  
Old 09-20-2014, 10:00 AM
Caleb's Avatar
Caleb Caleb is offline
COTEP Member
 
Join Date: Sep 2013
Location: Earth
Posts: 11,463
Thanks: 4,192
Thanked 1,137 Times in 254 Posts
Default

He is a wealth of knowledge, thanks.
__________________
**I have been Enlightened**
Reply With Quote
Reply




All times are GMT -4. The time now is 03:42 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.