![]() |
|
Register | Forums | Blogs | Today's Posts | Search | Donate |
![]() |
![]() |
![]() |
#1
|
||||
|
||||
![]()
I'm looking to have some minor mod's done to my Colt Gov't model 70 series. I want to change to a beavertail, which I know will require new hammer and I assume sear. If I'm going to do that I might as well change the trigger, slide release, and safety (the pistol is hard chrome and the parts are silver, would like to change them to blue/black). Any recommendations as to what brand parts to purchase? Any other changes that should or must be made? Thanks in advance..
__________________
CBOB0718 |
#2
|
||||
|
||||
![]()
I replaced the fire control group in my Colt Combat Elite a couple of years ago with a Cylinder and Slide kit from Brownells. Pre cut sear / hammer.
It is first class, very well made and required minimal fitting. Marc |
#3
|
||||
|
||||
![]()
Thanks. I'll check them out.
__________________
CBOB0718 |
#4
|
|||||
|
|||||
![]()
yep, the kits are the way to go. I have expericne with EB and they are very good too. Very little fitting needed, good stuff. C&S stuff is also very good, have had a few of the parts from them folks and also good stuff.
__________________
![]() |
#5
|
|||||
|
|||||
![]()
All three companies listed make good kits..a word of advice..PM Dave Waits here...he'll tell you if you need any more parts to complete what you want..and what fitting may be required. He's been busy lately, so a PM is the best way to go and if that don't work, let me know and I'll email him
__________________
NRA Life Member Wilson Combat CQB Kimber Tactical Pro II S&W J-Frame .38 ect " I don't own the clothes I'm wearin', and the road goes on forever " ![]() There's a gator in the bushes, and it's calling my name... COTEP #523 |
#6
|
|||||
|
|||||
![]()
What he said! Think about a new set of pins.
__________________
canis fidelis cave canem, vereor non magnus nocens lupus In hoc signo vinces If you can list them, you ain't got enough!!! Life Member NRA, SCI, ATA, NSCA COTEP 414 |
#7
|
|
![]() Quote:
You're correct in that your existing Hammer, as it is, won't work with a beavertail. You have two options here, one, you can Bob your existing Hammer. This involves cutting off and blending about 1/8th inch off of your Spur. The other is to purchase one of the many kits out there. I like the Cylinder&Slide kits, specifically, the Tactical II 4lb. Kit. Has a Hammer,Sear, Disconnector, new searspring and hammer spring. Part number is Brownells #206-000-058WB, $143.99. It is a drop-in unit. It's also strongly advised to replace the Thumb-Safety also. If you like them, you can order a new stock thumb-safety from Colt or get one of the tons of Tactical Thumb-Safeties out there. Reason is, the existing thumb-safety may be cut too short already to work with the new parts. I recommend the Wilson Combat Bullet-Proof Slide-Stop as it has a .200 pin which will tighten up your lockup a bit and help with accuracy. Hope this helps, any questions just ask.
__________________
Diligentia, Vis, Celeritas COTEP#CBOB0428 NRA,GCA,OGCA, USAF,Msgt.(Ret.) |
#8
|
|||||
|
|||||
![]()
Thanks
![]()
__________________
NRA Life Member Wilson Combat CQB Kimber Tactical Pro II S&W J-Frame .38 ect " I don't own the clothes I'm wearin', and the road goes on forever " ![]() There's a gator in the bushes, and it's calling my name... COTEP #523 |
#9
|
||||
|
||||
![]() Quote:
__________________
CBOB0718 |