Slide Dropping in Mag Load

[Caleb]

I had a plastic gun that did the same thing, turned out to be a weak slide stop spring. I'm sure thats not the issue with yours since there is no spring there foe 1911s. Check for excessive wear on the slide and stop.

Here is a bad pic of a worn slide where the stop catches. Notice how it is angled backwards instead of a 90 deg.

[Grouse]

Originally Posted by IamCaleb

I had a plastic gun that did the same thing, turned out to be a weak slide stop spring. I'm sure thats not the issue with yours since there is no spring there foe 1911s. Check for excessive wear on the slide and stop.

Here is a bad pic of a worn slide where the stop catches. Notice how it is angled backwards instead of a 90 deg.

your picture sucks.... :P I fixed it for you

[Caleb]

Originally Posted by Grouse

your picture sucks.... :P I fixed it for you

... You are not right.

[milkmanjoe]

I have guns that are modified to do just that. I drop a mag, slam one home and the guns chamber a round. Maybe the previous owner did some filing. Glocks are famous for this "failure" to stay locked back.

[GD2A]

Originally Posted by milkmanjoe

I have guns that are modified to do just that. I drop a mag, slam one home and the guns chamber a round. Maybe the previous owner did some filing. Glocks are famous for this "failure" to stay locked back.

I'll never know for sure but I doubt the guy I bought it from had this done. Also, it didn't happen with several other mags. It happened randomly and when it did, I would drop the mag, clear the chamber and reload the top round back into the mag. Then I'd reinsert the same mag and NOT experience the same event.

Moreover, I see no signs of excessive wear. By outward appearances the gun is cherry and the slide cuts appear to be identical to my 1991 Commander that has run perfectly.

I also just looked at my NIB Combat Elite and the cut angles are the same. None are 90 degrees, FWIW (Using 's pic as a reference.)

[Caleb]

Originally Posted by GD2A

I'll never know for sure but I doubt the guy I bought it from had this done. Also, it didn't happen with several other mags. It happened randomly and when it did, I would drop the mag, clear the chamber and reload the top round back into the mag. Then I'd reinsert the same mag and NOT experience the same event.

Moreover, I see no signs of excessive wear. By outward appearances the gun is cherry and the slide cuts appear to be identical to my 1991 Commander that has run perfectly.

How hard are you slamming the mag home?

Like milk boy, I don't see a disadvantage as long as it feeds the top round properly every time. It's one less step you have to do.

[DaFadda]

I have a BERSA 380 that does this by design. Of course... 1911's aren't usually designed to do this. Bersa called it a "combat reload." If I slam the mag home, the gun strips a round and loads. I was.... like.... hmmmm.... don't know if I like that "option."
Da

[GD2A]

Originally Posted by IamCaleb

How hard are you slamming the mag home?

Like milk boy, I don't see a disadvantage as long as it feeds the top round properly every time. It's one less step you have to do.

That's tough to quantify but the same way I do all my 1911 mags - a solid shove home. I also posted this on the Colt Forum and somebody brought up 'buffers'. That made me remember that there is some sort of rubber ring on the guide rod - could that be a contributing factor?

[Riverpigusmc]

Check for a shockbuff on your guide rod, but that normally only affects slingshotting a compact gun. Check the lobe on your slide stop, the notch on your slide for peening, and your mag springs and followers. First place I would look is followers

[Riverpigusmc]

Field strip the pistol, take off the grips, put the slide stop back in, then slide a loaded mag in and see where the first round is contacting the slide stop