Ambi safety / break in. New Vbob on the way.

[GoldenVolt]

Clean it, lube it, shoot it and repeat.

It would be best to oil the rails every 100 round until 500 round count.

When I get a new one I wont go over 150 rounds in one session. Cleaning it after every range trip, until 1000 rounds through the pipe.




Is Kimber the only one doing this style?????.....



Greg

[Mike45]

I was going to recommend a Kimber also as they seam to be the easiest to disassemble and do not come loose, at least mine don't.

I see that Wilson has a new ambi I have seen that some have had some problems installing it, probably working out some of the bugs and it seams a bit complicated.

Keep grease on the rails and keep the gun well oiled.

[Dave Waits]

Just to add to the posts already made, I would suggest, not saying you have to do it, running a couple boxes of WWB 230FMJs through it with the gun well-lubed. As was stated, most modern 1911s are pretty tight from the factory. I always do that to help smooth the gun out and remove any tight spots.Before any of you purists attack, I know it's one of the annointed DWs but, seeing as how my oldest son just purchased an Ed Brown that went through the 'New,tight-gun' syndrome, it just shows that any new firearm can have these problems.

As for an Ambi Thumb-Safety, I'm a lefty myself. I've had a Cylinder&Slide 'High-Grip' Ambi on my Rock for over 14,000 rounds, still tight,still positive. As with many things, the devil is in the details, it has to be fitted correctly. That said, Kimbers' Ambi with the extended Hammer-pin is probably the best
Ambi out there. It's based pretty closely on the old Kings' Gunworks design and won't come apart, very positive. I had one on my Pro Carry II and it worked very well.

Ambi's, or even one-sided Thumb-Safeties that break or come loose, were not installed correctly to begin with. If you go to the Dremel Room you'll find some photos I posted of both how a Thumb-Safety works and what needs to be fitted. Just remember to go slow and file a little bit at a time lightly, especially on the ledge (Sear Engagement area).
Here's a link to the photos; http://www.cotep.org/forum/showthread.php?t=646

[BBP]

Originally Posted by Dave Waits

Just to add to the posts already made, I would suggest, not saying you have to do it, running a couple boxes of WWB 230FMJs through it with the gun well-lubed. As was stated, most modern 1911s are pretty tight from the factory. I always do that to help smooth the gun out and remove any tight spots.Before any of you purists attack, I know it's one of the annointed DWs but, seeing as how my oldest son just purchased an Ed Brown that went through the 'New,tight-gun' syndrome, it just shows that any new firearm can have these problems.

As for an Ambi Thumb-Safety, I'm a lefty myself. I've had a Cylinder&Slide 'High-Grip' Ambi on my Rock for over 14,000 rounds, still tight,still positive. As with many things, the devil is in the details, it has to be fitted correctly. That said, Kimbers' Ambi with the extended Hammer-pin is probably the best
Ambi out there. It's based pretty closely on the old Kings' Gunworks design and won't come apart, very positive. I had one on my Pro Carry II and it worked very well.

Ambi's, or even one-sided Thumb-Safeties that break or come loose, were not installed correctly to begin with. If you go to the Dremel Room you'll find some photos I posted of both how a Thumb-Safety works and what needs to be fitted. Just remember to go slow and file a little bit at a time lightly, especially on the ledge (Sear Engagement area).
Here's a link to the photos; http://www.cotep.org/forum/showthread.php?t=646

Thanks for the info. Looks complicated and having to file. I think it will just go to our local gunsmith. Going to order the safety and take it to him. Do you know if the Kimber color matches the duty black vbob?

Thanks